Use this LED puck light kit to brighten kitchen counter areas, work spaces and more. They are also perfect for small areas, such as closets or kitchen cabinets. The kit includes 4 LED puck lights, cables, plug-in transformer power supply and remote control. 6-foot power cord. 5-feet of wire on each light. Includes mounting supplies.
I would like to light upper and lower cabinets on two walls of my kitchen. this would require 3 sets. Would I be able to control all 3 at the same time with one remote?
A shopper
on Mar 9, 2018
BEST ANSWER:Yes, all the remotes are set to the same frequency set by the manufacturer.
BEST ANSWER:We have our in the top of our high kitchen cabinets. I think your only limitation is the length of the cord to an outlet . They were easy to install and look great.
BEST ANSWER:We have our in the top of our high kitchen cabinets. I think your only limitation is the length of the cord to an outlet . They were easy to install and look great.
BEST ANSWER:I mounted two of eights light's ( needed two sets for my project) inside cabinets, the rest on the outside along with the receiver. So while I can't say for certain that the signal would not go through a cabinet door, I can say that I have to be practically right at the receiver with the remote for the lights to turn on. That being said, you could always install the lights with the receiver on the outside of the cabinet. Hope that helps. C.
BEST ANSWER:I mounted two of eights light's ( needed two sets for my project) inside cabinets, the rest on the outside along with the receiver. So while I can't say for certain that the signal would not go through a cabinet door, I can say that I have to be practically right at the receiver with the remote for the lights to turn on. That being said, you could always install the lights with the receiver on the outside of the cabinet. Hope that helps. C.
Do the wires disconnect from the puck lights so they can be run on the inside of the cabinet and then drill through the cabinet bottom to mount them to the underside? This way the wires would be on the inside of the cabinet and hidden. Matt
BEST ANSWER:The wires are connected to the lamps ! The install is easy! The wires are not connected to the transformer. Just drill the hole at the bottom of the cabinet were you will mount the lights. Run the wires inside the cabinet to the transformer. If you have a outlet inside the cabinet. ( microwave mounted to a cabinet ) then there is no issues. Install time about ten minutes. You will need Velcro to mount the lights under the cabinet. The furnished tape will not hold long. Also the remote will not work if the cabinets doors are closed. You will need open the cabinets to turn on and shut off! The install is easy if you have a outlet in one of the cabinets!
BEST ANSWER:The wires are connected to the lamps ! The install is easy! The wires are not connected to the transformer. Just drill the hole at the bottom of the cabinet were you will mount the lights. Run the wires inside the cabinet to the transformer. If you have a outlet inside the cabinet. ( microwave mounted to a cabinet ) then there is no issues. Install time about ten minutes. You will need Velcro to mount the lights under the cabinet. The furnished tape will not hold long. Also the remote will not work if the cabinets doors are closed. You will need open the cabinets to turn on and shut off! The install is easy if you have a outlet in one of the cabinets!
Can these pucks be embedded in underside of cabinets? FYI, my cabinets were refaced and the bottoms covered with 1/4 inch thick stained alder. It would be easy to cut out a round hole.
I know that the cords from the lights to the connector box and from the connector to the transformer cannot be shortened, but CAN THE CORD FROM THE TRANSFORMER TO THE PLUG BE SHORTENED?
BEST ANSWER:Since the cord that runs from the plug to the transformer is all one piece we do not recommend to shorten the wire as it will have to be cut and spliced.
BEST ANSWER:Since the cord that runs from the plug to the transformer is all one piece we do not recommend to shorten the wire as it will have to be cut and spliced.
They are VERY thin. I think cutting and splicing would be hard, if not impossible. I just got some 3M Command hooks to hold the excess cord that I wound into a lasso-type coil.
Hi Mike B., thank you for the review. Would you please reach out to our customer service team? We'd like to hear more about the issues you are experiencing with this kit so that we can help troubleshoot. Thank you.
December 18, 2017
Stacy M.
Staff
Nice Kit
They work great, were easy to install and give plenty of light.
Open Box
