Lighting on the Square 21" Wide Bronze Bath Wall Light

This fits perfectly with our powder room decor and like the soft illumination. However, this was the most difficult fixture I have ever installed. Trying to attach the fixture to the base using the side mounting method as instructed did not yield good results for me. A better design would be to attach the fixture to the base from the front. This is acutely what I did and it did not detract from from beauty. Also, my wife, with her petite hands, had to install the globes and bulbs. No way was I going to do this with my average size male hands.

Pros: Attractive Design

Cons: Hard To Install, Difficult To Change Bulb

our master bathroom

Pros: Great Illumination, Attractive Design, Quality Construction

Cons: Difficult To Change Bulb, Hard To Install

This lamp is beautifully designed and built. We used three, 60w equivalent A15 bulbs, and put it on a dimmer switch. We located it at the bottom of our stairway. Couldn't be happier with the result. Turned down low, it makes a great accent light. Turned up high, it makes very bright, but even light.

I would recommend this product to someone handy. Might not work as well for a hired electrician, depending on their patience with tiny screws and customization of the base plate. As previously reviewed, there are tiny screws that must be inserted in a fairly inaccessible spot for hanging. My husband needed to fine tune the base plate by drilling extra holes, because as purchased, the base plate was crooked. Once hung, the light looks great. Keep in mind it takes 3 forty watt bulbs, which in our case is a little too dim. Even with that, it’s a good look for the price.

It was packed well. One side of the box was gouged but the fixture itself was undamaged.

I concur with others who say this is difficult to install. Four small bolts must be screwed sideways into mounting plate. However 3 of the 4 bolts are blocked metal parts of the fixture, leaving only a small distance beyond the bolt head. Included is an allen wrench with a phillips head, but the phillips head is on the long side not the short side, and the long side is too long to fit. I had to go looking for other tools and eventually managed.

Each globe has a round opening on the base. On one of my fixture's three three globes this opening wasn't quite round and would not admit the metal sleeve. I took a convex metal file to it. Fortunately it did not crack and, after about 300 scrapes, I was able to jam in the metal sleeve. Still, it was a much tighter fit than with the other two globes, and I worry that something like heat expansion might cause it to crack later.

Each of the three globes had a cosmetic issue (such as a dot passing more light than the remainder of the globe) on one of its long sides, but in each case I was able to put the flawed side toward the back. The front-facing sides look fine. But you may want to check how they look with the light bulb installed before tightening the rings that hold the globes in. They are a bit cumbersome to tighten, so best if you only have to do it once.

I installed the fixture with the globes facing up. There's no reason it couldn't be installed with the globes facing down, though the mounting plate is not symmetrical, so you should decide which way you want it before attaching the mounting plate to the wall. I will point out that (with the globes facing up) the bottom of the lower metal bar is smooth, but the top of the top metal bar has slightly raised black circles at each corner. If it were mounted with the globes facing down, these small circles would be visible to someone standing below, though I doubt many would notice them.

A hidden sticker warns 40 watts max per bulb, which isn't really an issue in the post-incandescent age.

First, DO NOT try to install this fixture on the wall with the glass shades in place!! ... it will make access to the mounting screws MUCH, MUCH easier! Second, for the proper bathroom "cool" illumination (no orange light), purchase three "A15" LED bulbs with 800 lumens, at least 8 watts, and a temperature of 6,000K (see photos). If you wish to use a "dimmer", make sure you purchase the special On/Off switch and bulbs required to allow for dimming. Unlike a few other purchasers, I had absolutely no problem with the installation. An elegant answer for a bathroom vanity!

Looks great in my new powder room. Plenty of light with the lowest watt bulbs available

Looks great over the vanity in our bathroom

Modern design that enhanced the bathroom.

Pros: Quality Construction, Great Value, Attractive Design, Great Illumination

Best Uses: Small Rooms, Decoration

Awesome light fixture. We are remodeling out bathroom and this light fixture complements our tiles, countertop and bathroom vanity perfectly.

Very nice. We wanted something that was not just like everything else (I.e., not what you can find at the big box home-improvement stores). This one fit the bill! Wish it came in other colors though; such pewter

The light fixture is absolutely perfect for my small powder room. It's sleek and not bulky.

easy to install .elegant. what I was looking for .

It is very attractive and adds the right amount of light to our small guest bathroom.

Love the lighting choices for Arts and Crafts.

the look great, but still yet to have them installed.

The look of the light once installed and fiddled with is great. Couple things... The top and bottom bar are not exactly parallel so I leveled half way and it looks good. The bases that the globes sit on are welded slightly leaning right. All six (two separate lights). Might put some hidden washers under the globe yo level. As others have stated, the screws are a bit of a pain. I used a long skinny screwdriver and that worked. My experience and skill level is high.

It didn't come with lights. What kind of bulb should I buy?

Electrician had a hard time installing as the side screws were very hard to get to. I ended up having to try and tighten them since the angle and reach were impossible for a mans fingers. Also the ceramic base was crooked and got the base in crooked. No way to adjust since it was stuck. And the light bulbs are much dimmer.

It was easy to place an order with you, and then the fixture came quickly - showing efficiency and caring about customer's needs